| Status |
ExpNbr |
Date |
Author |
Type |
Category |
Target-Source |
Subject |
Text |
 |
| Ongoing | e744 |
Sun May 13 19:36:09 2018 |
Valérian + François | MUST2 | General | 3-alpha | Run #116 #117 3 alpha run Calibration T1-T5 trigger | [U][B]run #116[/B][/U]
start @12h07 13/05/18
stop @19h45 13/05/18
|
|
| Fixed | e748 |
Thu Jun 22 11:10:35 2017 |
Valérian | EXL | Software | | EXL Mapping | Mapping of the EXL detector in the analysis
program versus how it is written on the cables. |
|
| Fixed | e748 |
Mon Jun 26 10:26:16 2017 |
Valérian | EXL | Software | 60Co | Add-back | We implemented the add-back correction with
cross-talk subtraction.
|
|
| Fixed | e744 |
Wed Apr 25 15:59:51 2018 |
Valérian | EXL-PPT | Software | N/A | Mesytech setup | To use the remote settings of the Mesytech
modules :
[CODE]
|
|
| Ongoing | e744 |
Tue May 15 09:58:52 2018 |
Valérian | RUN | General | 3-alpha | run #118 3 alpha | [U][B]run #118[/B][/U]
Trigger T1 T2 T3 T4 & T5
EXL + BT not biased but still in trigger
|
|
| Fixed | e744 |
Tue May 15 19:42:40 2018 |
Valérian | EXL-PPT | General | 60Co | Calibration of EXL from e748 data | The EXL calibration program is ready. Join
is the result with previous data from e748. |
|
| Fixed | e744 |
Fri Jun 1 13:12:16 2018 |
Valérian | EXL-PPT | General | 60Co | run #3003 Calib EXL | run #3003
start @12h06
stop @13h08 |
|
| Fixed | e744 |
Fri Jun 1 19:29:17 2018 |
Valérian | EXL-PPT | General | 60Co | EXL efficiency | To test EXL efficiency I start a long run
with the source in front of it.
run 3014
|
|
| Ongoing | e748 |
Tue Jun 6 17:57:07 2017 |
Valérian et François | EXL | Hardware | | Hardware coupling of EXL with MUST2 |
EXL seems to fit in Adrien's setup. We still
have to check if it fits in the chamber. |
|
| Ongoing | e744 |
Sat May 26 07:32:17 2018 |
Valerian, pedja, mihai | RUN | General | CH2 | Run 2015 after vacuum problem of Css1 target 4 | [U][B]Run 2015[/B][/U]
26/05/18
start @7h29
|
|
| Ongoing | e744 |
Wed May 30 11:17:00 2018 |
Valerian maurycy and Olivier | OFFLINE | General | CH2 | Condition on time T5 | One should add the condition Si_TX < 150 for
T5, problem from Ta? |
|
| Ongoing | e744 |
Wed May 30 11:22:16 2018 |
Valerian maurycy and Olivier | OFFLINE | General | CH2 | Checking the cuts | cut_DeE :
- T1 OK
|
|
| Ongoing | e744 |
Mon May 28 20:28:50 2018 |
Valerian and Simon | OFFLINE | General | CH2 | Explanation for the 0 degree low energy proton | The 0 degree energy proton are coming from
the beam hitting the aluminum target. If
you do a cut on the beam projection on T5 |
|
| Fixed | e744 |
Mon May 28 11:00:07 2018 |
Valerian and Iulian and Phil | RUN | General | | two protons | |
|
| Ongoing | e744 |
Mon May 28 23:14:26 2018 |
Valerian and Iulian and Phil | OFFLINE | General | CH2 | New hint of the 5/2- resonance | We see a new hint of a resonance |
|
| Ongoing | e744 |
Sat May 26 07:03:12 2018 |
Valerian and Iulian and Francois | OFFLINE | General | CH2 | First picture for 15F from runs 2010-2013 | Target -> Thick target (Sandwich target ??)
The predictions are different....
|
|
| Ongoing | e744 |
Sat Apr 28 10:17:22 2018 |
Valerian and Iulian | MUST2 | Hardware | 3-alpha | Status of MUST2 telescopes 27/04/18 | Yesterday night we tested T1, T2, T3, T4,
T5, and T6.
|
|
| Ongoing | e744 |
Sat Apr 28 13:27:26 2018 |
Valerian and Iulian | MUST2 | Hardware | 3-alpha | multiples runs with two alpha source on T1 T2 T3 T4 and T5 | For the following runs we will use two 3 alpha
sources :
|
|
| Ongoing | e744 |
Sat Apr 28 13:36:52 2018 |
Valerian and Iulian | OTHER | Software | N/A | Problem with DAS configuration | There is an issue with the GMT slave. When
you click Online and then apply write hardware,
if the message : [U]register error on GMTSlave[/U] |
|
| Ongoing | e744 |
Fri May 25 02:57:44 2018 |
Valerian and Iulian | OFFLINE | General | CH2 | Simulation Azure 1H(14N,p) and measurement | We can know conclude without any doubt that
we were able to measure resonances from 1H(14N,p)14N.
The resolution with a rough analysis and |
|