| Status |
ExpNbr |
Date |
Author |
Type |
Category |
Target-Source |
Subject |
Text |
 |
| Fixed | e748 |
Fri Jun 9 14:41:54 2017 |
e748 | CATS | General | | Runs 1 - 4 | Tests alpha source, dummy data |
|
| Pinned | e748 |
Fri Jun 9 15:49:46 2017 |
Valérie Lapoux | MUST2 | Hardware | | MUST2 configuration | The MUST2 configurations for telescopes in
the chamber and low/High voltage Caen crate
are given in the attached file. |
|
| Pinned | e748 |
Fri Jun 9 15:51:44 2017 |
Valérie Lapoux | MUST2 | Hardware | | General Trigger GMT for MUST2 electronics | The GMT configuration for the trigger inputs
and the inputs from MUST2 electronics are
given in the file. |
|
| Fixed | e748 |
Mon Jun 12 11:34:07 2017 |
e748 | MUST2 | Hardware | | MUVI cars setup | We had problem with MUVI1 (pre serie 1) not
working properly when a telescope was pluggeg
(but fine otherwise).
|
|
| Fixed | e748 |
Mon Jun 12 11:36:34 2017 |
e748 | MUST2 | Hardware | | I2C error on Telescope | At the Moment we got I2C error on the following
detectors:
|
|
| Fixed | e748 |
Mon Jun 12 11:50:34 2017 |
e748 | CATS | Software | | Settings QDC | Gates QDC CATS1X, CATS1Y, CATS2X, CATS2Y:
0.996
Pedestal QDC CATS1X, CATS1Y, CATS2X: 0.5
|
|
| Fixed | e748 |
Mon Jun 12 11:52:16 2017 |
e748 | CATS | General | | Run 6 and 7: Calibration Runs CATS | Run 6: Calib CATS1 X&Y
--> Full, x2, x5, pedestal
|
|
| Fixed | e748 |
Mon Jun 12 11:55:27 2017 |
e748 | CATS | General | | Run 5 - JUNK pulser run on CATS1 | Dummy run with pulser.
JUNK |
|
| Fixed | e748 |
Mon Jun 12 14:09:24 2017 |
e748 | CATS | Software | | calibration coefficients Runs 6-7 | columns are for 1st order calib (y= ax + b):
pedestal - b - a |
|
| Fixed | e748 |
Mon Jun 12 16:56:36 2017 |
e748 | OTHER | General | | e748 Proposal | Experiment proposal |
|
| Fixed | e748 |
Mon Jun 12 22:48:45 2017 |
Valérie Lapoux | MUST2 | General | | Tests of the DAQ with the Alpha Source | 12Th June. 3-peak Alpha source rotated towards
the telescopes MM1 to MM4 (square wall of
4 telescopes).
|
8x |
| Pinned | e748 |
Tue Jun 13 11:14:23 2017 |
Valérie Lapoux | MUST2 | General | | GMT configuration, FAG | The Gatconf parameter is now defined in the
action file.
The new configuration for GMT (see chronogramme |
|
| Fixed | e748 |
Wed Jun 14 12:13:00 2017 |
e748 | MUST2 | Hardware | | MUST2 I2C Err debugging | It appears several SL cables are faulty.
To avoid manipulation of all the cable we
now have T1-4 working. These required to |
|
| Pinned | e748 |
Thu Jun 15 10:16:03 2017 |
Valérie Lapoux | MUST2 | Hardware | | Electronics for GMT trigger and FAG | The GMT is used in a mode where we do not
make coincidence and decision, GMT entries
are single and all accepted as triggers of |
|
| Fixed | e748 |
Thu Jun 15 17:51:15 2017 |
e748 | RUN | General | 3-alpha | Run 5-7 | [SIZE=3]run5[/SIZE]
alpha source
|
|
| Fixed | e748 |
Fri Jun 16 09:57:54 2017 |
e748 | RUN | General | 3-alpha | Run 11 | RUN 11 : alpha calibration with suppression
of zeros ( & alignment of pedestals) for
all night |
|
| Fixed | e748 |
Fri Jun 16 09:59:00 2017 |
e748 | RUN | General | 60Co | Run 12 | RUN 12 : EXL trigger in GMT
+ gamma source 60Co
|
|
| Fixed | e748 |
Sat Jun 17 10:22:43 2017 |
Adrien Matta | EXL | Hardware | | EXL ADC gate | EXL ADC is now setup with individual gate
on the ADC.
|
|
| Fixed | e748 |
Sat Jun 17 10:27:26 2017 |
Adrien Matta | ONLINE | Software | | Starting the GRU online analysis | We setup a script to start the right environment
to run GRU, ganil2root and nptool.
|
|
| Fixed | e748 |
Sat Jun 17 10:32:25 2017 |
Adrien Matta | ONLINE | Software | | Online/Offline list of task | We need to do the following improvement to
the online / offline environment:
|
|