MUST2 SAMURAI_2018 S3-LEB-LPC SUPERNEMO MUGAST EXPAND SCALP GALATRON HiCARI VELO
  MUST2, Page 26 of 48  Not logged in MUST2
Fixed, e744, Sat May 26 16:31:53 2018, Jaromir, Giuseppe, EXL-PPT, Software, N/A, EXL calibration, light leak batchSelector.CEXL.pdfpairs0102_0910.pdfpairs1112_1718.pdf
Selector.C can be used to adjust energy bad reconstruction in the EXL detectors due to energy leak (see the PDF attached for more information about it)
once we already have the coefficients for the energy on EXL crystals. To operate with it, for first calibration coefficient must be deduced. Once it is
done the slopes and offset of the calibration have to be inserted in Selector.C file at lines 41 (a[19]) and at line 49 (b[19]). After thqt thresholds
Ongoing, e744, Sat May 26 20:20:55 2018, Valerian, OFFLINE, General, CH2, 15F observations for target 4 (100um) Ecm_Thetacm_target4_notes.pdfEx_15F_proj_0_4deg_Ecm_target4.pdfEx_0to40degEcm_15F.pdf
Analysis offline permits us to conclude that the current target has the good size to observe our resonances.
Ongoing, e744, Sat May 26 20:23:52 2018, Cristina Iulian, OFFLINE, General, , PPT gamma spectrum runs_target4_proton_prompt_PPT.pdf
 Attached is the gamma spectrum from PPT detector with a condition on prompt (T_MM_PPT), proton detected in MUST and multiplicity event equal to 1
Pending, e744, Sun May 27 15:36:31 2018, François, BEAM, Social, , News updated 
19H
They succeeded to get 90 % transmission with CSS1 but the energy at the exit was changed by 4%, that is not compatible with the CSS2 limit of 1 %. After
fitting the CSS1 energy they obtained 70-80 % transmission only, but it is enough.  The problem with the HF of CSS2 was solved. They are trying to accelerate
Fixed, e744, Sun May 27 20:47:02 2018, e744- Valérie, DAQ, Hardware, N/A, Info to reboot the crates in case of problem IOLANmust2reboot.pngRunControlE744Ready.png
In case of problems in the run control, if it is not possible to reinstall the crates in the  "Ready" mode status, 
it is possible to reboot them remotely via the software commands.
this can be done using the iolan windows.
Ongoing, e744, Mon May 28 02:07:41 2018, Valerian, OFFLINE, General, CH2, New improved resolution for 14N et 15F Exc_15O_newpos.pdfExc_15F_newpos.pdf
After correcting position for the Must2 detectors by taking into account the real hit position on the target that was (0,15cm,0) and not (0,0,0). The way
to do it was to artificially move every detector 15cm lower.
Fixed, e744, Mon May 28 11:00:07 2018, Valerian and Iulian and Phil, RUN, General, , two protons  e2p_15O.pdf
 
Fixed, e744, Mon May 28 12:22:42 2018, Francois & Marlete, OFFLINE, General, , superposition exp / theory for 15O and 15F sum.jpg15F_final.jpg
 
Pending, e744, Mon May 28 16:14:29 2018, François & Valérie, MUST2, General, N/A, Cooling system 
 Monday 28th 16h10: we refill the cooling system for MUST2. The level should be ok for the rest of the experiment.
(Around 4 days).
Fixed, e744, Mon May 28 16:32:38 2018, E744- Valérie, DAQ, General, N/A, DAS configuration files-References 15x
 
Fixed, e744, Mon May 28 18:27:45 2018, E744- Valérie, DAQ, General, N/A, High Voltages and intensities on MUST2 HT_MUST2withoutBeam28may18.png
 Check regularly the HT on the MUST2.
NB: without beam the current on Telescope 4 is high, between 9 and 11 µA. see snapshot.
NB: The Ioset was increased at 20 µA on Friday 25th (cf Id entry=490) to avoid trips on this telescope due to strong intensity fluctuations due to the
Ongoing, e744, Mon May 28 20:28:50 2018, Valerian and Simon, OFFLINE, General, CH2, Explanation for the 0 degree low energy proton explanation_spotT5.pdf
The 0 degree energy proton are coming from the beam hitting the aluminum target. If you do a cut on the beam projection on T5 you obtain the black dot on
the joined plot.
Fixed, e744, Mon May 28 20:33:39 2018, E744- evening shift LISE+e744 teams (edit Iulan, Valérie), RUN, General, CH2, BEAM AGAIN RUN 2100 Tuning beam_spot_2100_end.png
  See plot of the Must2 impacts, Wien filter set at +/-0.8kV  
Beam on CATS 1.2 10**5 pps
CH2 183 µm
Fixed, e744, Mon May 28 20:38:21 2018, E744- evening shift LISE+MUST2 teams (edit Valérie), RUN, General, CH2, RUN 2101 DATA target 4 12x
[U][B]run #2101[/B][/U]
start @20h27
stop  @22h20
Fixed, e744, Mon May 28 22:11:52 2018, e748- Louis, EXL-PPT, Hardware, CH2, EXL4 trigger excess Scaler_EXLTriggerExeed_Run2101.png
During run 2101, Frequency of the EXL4 channel at 478Hz compared to values around 30Hz for other channels
Fixed, e744, Mon May 28 22:27:14 2018, Simon et Louis, RUN, General, CH2, RUN 2102 DATA target 4  Scaler_start_Run2102.pngScaler_stop_Run2102.png
run #2102
start @22h20
stop @23h30
Ongoing, e744, Mon May 28 23:14:26 2018, Valerian and Iulian and Phil, OFFLINE, General, CH2, New hint of the 5/2- resonance New_resonance_hint.pdf
We see a new hint of a resonance
Fixed, e744, Mon May 28 23:52:19 2018, Simon and Louis (start), Franck (stop), RUN, General, Carbon, RUN 2103 DATA target 1 Carbon Scaler_start_Run2103.pngScaler_stop_Run2103.png
run #2103
start @23h49
stop @1h51
Ongoing, e744, Tue May 29 00:17:18 2018, Night shifter, BEAM, General, Carbon, Beam intensity variation hv_run2103.png
Beam shut down at 00h03. Increase the intensity progressively up to now 00h18.
At 0:28: primary intensity dropped down to 0.
Fixed, e744, Tue May 29 01:08:22 2018, e748, BEAM, General, Carbon, Beam intensity 
At 0:46 primary beam intensity reaches 5 uA -> 1.5e5 pps on CATS.

ELOG Home Page