| Status |
ExpNbr |
Date |
Author |
Type |
Category |
Target-Source |
Subject |
| Pinned | e748 |
Tue Jun 13 11:14:23 2017 |
Valérie Lapoux | MUST2 | General | | GMT configuration, FAG |
The Gatconf parameter is now defined in the action file.
The new configuration for GMT (see chronogramme plot) is attached, with the FAG window width set at 100 ns. |
| Attachment 1: GMTconfigOKMust2FAG100ns.png
|
|
| Attachment 2: GMTtrigParamActions.png
|
|
| Attachment 3: GMTparamDASgatconf.png
|
|
| Pinned | e748 |
Thu Jun 15 10:16:03 2017 |
Valérie Lapoux | MUST2 | Hardware | | Electronics for GMT trigger and FAG |
The GMT is used in a mode where we do not make coincidence and decision, GMT entries are single and all accepted as triggers of the DAQ.
The FAG window for the GMT should be set at a low value, typically 100 ns. |
| Attachment 1: DaqElectronicsMUST2gmtforE748.pdf
|
|
| Fixed | e748 |
Wed Jun 28 10:52:15 2017 |
Valérie Lapoux | MUST2 | General | | Memo for CALIMERO MUST2 Time Calibration |
| Temporary file indicating the main steps for the time calibration of MUST2 using the Calimero DAQ package program. |
| Attachment 1: ConfigDAQDasCalimerov2017vlxTMP.pdf
|
|
| Fixed | e748 |
Wed Jun 28 10:54:34 2017 |
Valérie Lapoux | RUN | Software | | DAQ problems due to TCP/IP errors |
Problems occurred during the run #29 at 2h38 Wed. 28th June, with the following error messages written in the Run Control GUI window:
Error rcc MUST2:VMECOM :TCP error TCP/IP time-out |
| Attachment 1: ProblemRun29TCPerror.png
|
|
| Fixed | e748 |
Wed Jun 28 11:02:38 2017 |
Valérie Lapoux | RUN | General | 3-alpha | Calibration run #31 with Alpha source - MM5 and MM8 |
Run #31 started at 11:01, Wednesday 28th June.
The alpha source is rotated towards the telescopes 5, 8. |
| Attachment 1: Run31startNarvalAlphaSource.png
|
|
| Fixed | e748 |
Wed Jun 28 15:17:24 2017 |
Valérie Lapoux | RUN | General | | End of run 31-status |
Run #31 started at 11h01; stopped at 15h13
Problem on ganlx9 VME Chio
TIMEOUT on the stop process. |
| Attachment 1: Run31stopProbTimeoutGanlx9Chio.png
|
|
| Fixed | e748 |
Thu Jun 29 23:26:10 2017 |
Valérie Lapoux | RUN | General | Empty | ALL CALIMERO Time Calibration MUVI1 |
29 JUNE 2017
CONDITIONS FOR CALIMERO CALIBRATIONS
Time calibrator Period 20ns ; range 512 ns
storage /data/e748X/e748/acquisition/run
--------------------------------------------------------------------------
RUN 0035 started 22h01; stop 22:35
RUN 0035 (run_0035.dat.29-06-17_22h01m28s.1) started 22h35 stop at 22h50
MUVI 1 TRIGGER IN GMT: MM1, MM2, MM3, MM4
MATE validated: STRIP-X T (enable MUFEEX, disable SiLi )
1048576000 29 juin 22:35 run_0035.dat.29-06-17_22h01m28s
431554560 29 juin 22:50 run_0035.dat.29-06-17_22h01m28s.1
The time to calibrate all stripXT is 50 minutes, when the statistics requested for one spectrum is 100000.
NB: DSSD Telescope 2 tripped round 23h50 29 june !!! I ~ 4.9 µA
-------------------------------------------------------------------------
RUN 0038 started 23h03 ; stop 00H14 30 juin
MUVI 1 TRIGGER IN GMT: MM1, MM2, MM3, MM4
MATE validated: STRIP-Y T (enable MUFEEX, disable CsI)
Exxx 1048576000 29 juin 23:28 run_0038.dat.29-06-17_23h03m18s
Exxx 1048576000 29 juin 23:53 run_0038.dat.29-06-17_23h03m18s.1
Exxx 846856192 30 juin 00:14 run_0038.dat.29-06-17_23h03m18s.2
-------------------------------------------------------------------------- |
| Attachment 1: CalimeroRunControl.png
|
|
| Attachment 2: ConfigCalimeroStat.png
|
|
| Attachment 3: CalibTmuvi1Yperiod20nsrange600ns.png
|
|
| Attachment 4: TimeMust2X_MUVI1_uncalib.png
|
|
| Attachment 5: TimeMust2Y_MUVI1_uncalib.png
|
|
| Fixed | e748 |
Fri Jun 30 00:33:36 2017 |
Valérie Lapoux | RUN | General | Empty | ALL CALIMERO Time Calibration MUVI2 |
30 JUNE 2017
CONDITIONS FOR CALIMERO CALIBRATIONS
Time calibrator Period 20ns ; range 512 ns
storage /data/e748X/e748/acquisition/run
--------------------------------------------------------------------------
RUN 0039 started 0h19 ; stop 00H45
MUVI 2 TRIGGER IN GMT: MM5, MM6, MM7, MM8
BUT ALL MUVI2 MATE at 300 ns !!!!
MATE validated: STRIP-X T (enable MUFEEX, disable SiLi )
The time to calibrate all stripXT is 25 minutes, when the statistics requested for one spectrum is 50000.
Exxx 761004032 30 juin 00:45 run_0039.dat.30-06-17_00h19m45s
------------------------------------------------------------------------- |
| Attachment 1: CalibTimeMUVI2stripXT.png
|
|
| Attachment 2: SpectresMUVI2stripXT300ns.png
|
|
| Fixed | e748 |
Fri Jun 30 01:01:08 2017 |
Valérie Lapoux | RUN | General | Empty | ALL CALIMERO Time Calibration MUVI2 GOOD RUNS 600ns |
RANGE TAC MUST2 600ns
CALIMERO TIME CALIBRATOR PERIOD 20ns; Range 512ns
RUN 40 started 00H53 ; stop 30 juin 01:19
MUVI 2 TRIGGER IN GMT: MM5, MM6, MM7, MM8
MATE validated: STRIP-X T (enable MUFEEX, disable SiLi)
---------------------------------------------------------
RUN 41 started ; stop 30 juin stop 31st of june 01:47
MUVI 2 TRIGGER IN GMT: MM5, MM6, MM7, MM8
MATE validated: STRIP-Y T (enable MUFEEY, disable CsI)
--------------------------------------------------------- |
| Attachment 1: TimeMust2X_MUVI2_uncalib.png
|
|
| Attachment 2: TimeMust2Y_MUVI2_uncalib.png
|
|
| Fixed | e748 |
Fri Jun 30 12:24:17 2017 |
Valérie Lapoux | DAQ | General | | DAQ Parameters: TAC, Caviar, LISE D4, D6, Caviar |
|
| Attachment 1: DASParamVXIMust2CatsTACLise.png
|
|
| Attachment 2: DASParamVXIChioQDC.png
|
|
| Attachment 3: DASParamVXIChioADClisepar.png
|
|
| Fixed | e748 |
Fri Jun 30 16:49:49 2017 |
Valérie Lapoux | DAQ | General | | GMT triggers and chronograph |
Configurations for the GMT inputs.
30 June 2017 pm
all Must2 telescopes,
divided inputs: Cats 1 (IN9) and Cats2 (IN10); Plast (IN11); ChIo (IN12);
TriggerLISE (IN13).
GMT chronograph FAG 100ns; CT 5µs. |
| Attachment 1: DASConfigTriggerGMT.png
|
|
| Attachment 2: ChronogrammeGMT30juinFAG100nsCT5µs.png
|
|
| Fixed | e748 |
Fri Jun 30 16:55:04 2017 |
Valérie Lapoux | DAQ | General | | Run control for global DAQ with NUMEXO |
The run start/stop sequence for the global DAQ including the NUMEXO:
I. ssh e748chio@ganp976
pw (same as for the experiment)
II. start_acq e748chio
-->the RC window of the e748chio is opened
III. START (on the RC e748chio)
IV. START (on the RC e748)
V. STOP (on the RC e748)
VI. STOP (on the RC e748chio)
================================================================================== |
| Attachment 1: RunControlAll748ModeMonitoring.png
|
|
| Attachment 2: NarvalRunControlAllE748.png
|
|
| Fixed | e748 |
Fri Jun 30 17:53:35 2017 |
Valérie Lapoux | DAQ | General | | Scalers parameters U2M |
|
| Attachment 1: Actionse748ganlx11withU2M.png
|
|
| Attachment 2: ScalerAnalyzerU2M.png
|
|
| Fixed | e748 |
Fri Jun 30 20:46:16 2017 |
Valérie Lapoux | TARGET | General | | TARGET configuration |
List of the reaction target in the chamber from bottom to up:
6. EMPTY FRAME (no frame)
5. CD2 2.5 mg/cm2
4. CD2 1.5 mg/cm2
3. CD2 2.5 mg/cm2
2. CD2 1.5 mg/cm2
1. MASK
MASK viewed from the beam coming to the target position :
cf photograph of entry ELOG Id=83 https://caeelog.in2p3.fr/MUST2/83
____________________________
----*-----*-----*------
----------*-------------
----*-----*--*--*---
-------*-----*--------
----*-----*-----*------
_________________________
SYSTEM of 3 blocks to fix the target position :
I small one
II long one III long one; II = III
To have the target n°1 mask: no block
To have target n°2 block I
target n°3: block II
target n°4: blocks I+II
target n°5: blocks II+III
target n°6: blocks I+II+III |
| Fixed | e748 |
Sat Jul 1 14:32:02 2017 |
Valérie Lapoux | DAQ | General | | Scalers U2M, parameters |
U2M configuration +Actions ganlx11
The signals for the scalers are converted from NIM to ECL in a 16 channel module NIM-ECL.
The cable is PHYSICALLY connected from the NIM-ECL module to the U2M on Groups 1 & 2.
Normally we should read these scalers on the U2M from channel 1 to 16 BUT
we found that the good channels are running on channels 17 to 32. See below.
We have defined the actions for all possible channels of the U2M registers 1 to 16 (Groups 1 and 2), and 17 to 32
(Groups 3 and 4) |
| Attachment 1: ScalersU2Mok.png
|
|
| Attachment 2: CompilActionsganlx11ScalerGr1to4..png
|
|
| Fixed | e748 |
Sat Jul 1 14:45:17 2017 |
Valérie Lapoux | DAQ | General | | Parameters for correlation checkings |
The parameters to be used for the checking of the correlations between crates/VME/VXI and good running of the merging
conditions of the different DAQs are :
- for MUST2 VXI with the GMT: GATCONF
- for CATS VXI: DATATRIG
- for CHIO VXI: DATATRIG_CHIO
- for CAVIAR crate: CONFDEV
- for AGAVA: CONFDEV_AGAVA
Check correlations on the following bidim:
parameter T_PL_CATS1 coded in ADC VXI MUST2
parameter T_PLch_CATS1 coded in ADC VXI CHIO
check T_CATS1_CAV |
| Fixed | e748 |
Sat Jul 1 15:12:01 2017 |
Valérie Lapoux | ONLINE | Hardware | | Conditions for Bidiv and TAC 1st July 15pm |
(Update the file CONDTIONS748.txt during the experiment)
JULY 1st 15pm
Bidiv = 1 for CATS1 and 2
Bidiv = 10 for Plast and ChIo
TAC ranges
START STOP RANGE PARAMETER ADDRESS VXI MODULE
-------------------------------------------------------------------
-------------------------------------------------------------------
CATS1_FAG CAVIAR 1µs T_CATS1_CAV ADC VXI MUST2 add=19
CATS1_FAG CATS2_FAG 500ns T_CATS1_CAV ADC VXI MUST2 add=20
OU_MUVI CATS1_FAG 500ns T_MUVI_CATS1 ADC VXI MUST2 add=21
PLAST_FAG CATS1_FAG 1µs T_PL_CATS2 ADC VXI MUST2 add=22
PLAST_FAG CATS1_FAG 1µs T_PL_CATS1 ADC VXI MUST2 add=23
-------------------------------------------------------------------
PLAST_FAG CATS1_FAG 1µs T_PLch_CATS1 ADC VXI CHIO add=19
PLAST_FAG CHIO 1µs T_PL_CHIO ADC VXI CHIO add=3
-------------------------------------------------------------------
------------------------------------------------------------------- |
| Fixed | e748 |
Sun Jul 2 08:06:53 2017 |
Valérie Lapoux | RUN | General | CD2 | Run 77 global check |
Conditions of Run 77
2 July - start at 6h29 - stop at 8h38
e748 Exxx 126943232 2 juil. 08:38 run_0077.dat.02-07-17_06h29m23s
N.B: The run is stopped at 8h38 to check the bidim of correlations TPL_CATS1 coded in VXI MUST2 and VXI CHIO.
GMT Triggers all MUST2 T1 to T8
----------------------------------------------------------------------------------------------------
CD2 2.5 mg/cm2 POSITION 3
CATS rate ~ 10 K/s to 12K /s; SCaler Analyzer see plot below
Muvi1 and Muvi2 counting rates: plots below
The merge configuration is checked with the parameters CONFDEV GATCONF etc...see plot below at 8h00
---------------------------------------------------------------------------------------------------- |
| Attachment 1: CheckMergeConf2july17at8h00.png
|
|
| Attachment 2: RunControlOnlineNarvalRun77.png
|
|
| Attachment 3: ScalerAnalyzerRun77At8h15.png
|
|
| Attachment 4: ScalerMuvi1Run77.png
|
|
| Attachment 5: ScalerMuvi2Run77.png
|
|
| Attachment 6: GMTConfigRun77.png
|
|
| Fixed | e748 |
Sun Jul 2 08:40:25 2017 |
Valérie Lapoux | RUN | General | CD2 | Run 78 - 2 July - 18O beam |
Run #78 CD2 2.5 mg/cm2 position 3 - 18O beam
Same conditions as for Run 77
Triggers all MUST2, T1 to T8, GMT IN1 to IN8
RUN 78 2nd July START at 8h39, STOP 10h01
e748 Exxx 92405760 2 juil. 10:01 run_0078.dat.02-07-17_08h39m30s
STOP of the beam and of the run to enter in D6, to make some checking of electronics and of the timing. |
| Attachment 1: Run78ConfdevDataTrig.png
|
|
| Attachment 2: RUN78tPLcats1CORREL.png
|
|
| Attachment 3: Run78CorrelWindowtimePlastCats1.png
|
|
| Attachment 4: Run78TACplastCats.png
|
|
| Attachment 5: Run78TrigMM2impact.png
|
|
| Fixed | e748 |
Sun Jul 2 08:46:13 2017 |
Valérie Lapoux | DAQ | Hardware | CD2 | Summary of the TAC conditions |
JULY 2nd 8pm
Bidiv = 1 for CATS1 and 2
Bidiv = 1 for Plast and ChIo
TAC ranges
START STOP RANGE PARAMETER ADDRESS VXI MODULE
-------------------------------------------------------------------------------------------
-------------------------------------------------------------------------------------------
CATS1_FAG CAVIAR (del 550ns) 1µs T_CATS1_CAV ADC VXI MUST2 add=19
CATS1_FAG CATS2_FAG (del 33ns) 200ns T_CATS1_2 ADC VXI MUST2 add=28
OU_MUVI CATS1_FAG 500ns T_MUVI_CATS1 ADC VXI MUST2 add=21
CATS2_FAG PLAST (val) 1µs T_PL_CATS2 ADC VXI MUST2 add=22
CATS1_FAG PLAST (no val) 1µs T_PL_CATS1 ADC VXI MUST2 add=23
-------------------------------------------------------------------------------------------
CATS1_FAG PLAST (no val) 1µs T_PLch_CATS1 ADC VXI CHIO add=19
PLAST val Gamer ChIo CHIO (no val) 2µs T_PL_CHIO ADC VXI CHIO add=3
-------------------------------------------------------------------------------------------
TAC EXL HF 100ns EXL_HF ADC VXI MUST2 add=18
------------------------------------------------------------------------------------------- |