Fixed, e768s, Fri Jul 26 19:00:15 2019, mugast, ONLINE, General, , Run number 152_2 19x
|
| |
|
Fixed, e768s, Fri Jul 26 19:36:03 2019, Kseniia, AGATA, General, , 19Ne gammas, current full stat
|
19Ne, VAMOS-identified
All runs from before + runs 151, 152part |
|
Fixed, e768s, Sat Jul 27 11:02:13 2019, mugast, ONLINE, General, , figures run 152 18x
|
| |
|
Fixed, e768s, Sat Jul 27 21:12:47 2019, teodora & beyhan, OTHER, Hardware, , cout rate with no beam & water level check 6x
|
Around 9 pm, we observed an average count rate of 30kHz on the "or agata" scaler rates panel of GECO. The other count rates were ok.
In the agata acquisition monitoring the rate was given about 8k. one of the detector was showing a rate in red.
|
|
Fixed, e768s, Sat Jul 27 22:22:21 2019, teodora & beyhan, VAMOS, Hardware, , FP_DC_Wi1 tripped -->Fixed
|
FP_DC_Wi1 tripped. We set back power supply on the wire
=> fixed |
|
Fixed, e768s, Sun Jul 28 08:20:38 2019, Sylvain & Franco, RUN, General, , Update on possible restart
|
The problem that caused the interruption was due to a failure in the cooling system.
The last update we've had is that we might have the beam back not before late afternoon.
We will keep you updated. |
|
Fixed, e768s, Sun Jul 28 16:23:48 2019, Nicolas, RUN, General, , Update on possible restart
|
| Same situation as before lunch, the beam is still in C0 and not yet in CSS1. We may have beam in late evening.... |
|
Ongoing, e768s, Sun Jul 28 19:58:57 2019, Nicolas, RUN, General, , Update on possible restart
|
| Beam is now at the exit of CSS2 though We may have beam around midnight....[/quote] |
|
Fixed, e768s, Sun Jul 28 21:59:43 2019, Nicolas, RUN, General, , Update on possible restart
|
| Beam is in G1 with 3e6 pps. PCP will optimize for about 1-1,5h before we take the beam. |
|
Fixed, e768s, Tue Jul 30 15:47:46 2019, Nicolas, BEAM, General, , Beam stopped since 11h30
|
| vacuum problem in CSS1 |
|
Fixed, e768s, Wed Jul 31 03:22:42 2019, Freddy, Chloé, BEAM, General, , Beam profile (run160) @2h24
|
| |
|
Fixed, e768s, Wed Jul 31 23:06:04 2019, Nicolas & Fairouz, OTHER, General, , screenshot fsc
|
| |
|
Fixed, TEST, Tue Dec 3 18:14:45 2019, Marlène & Franco, GRIT, Hardware, , Pulser test of new board
|
| The new board that will be installed for MG2 has been tested and validated with a pulser outside of the chamber. |
|
Fixed, TEST, Wed Dec 4 19:19:38 2019, Marlène, GRIT, Hardware, , Modifications of set-up
|
We have installed the new MUFEE board in the reaction chamber for MG2. This board is a new version with ATHED.
We have moved the MG9 board to become the board to read the future MUST2 detector at 90 deg. This board is now perpendicular to the other ones. We have |
|
Pending, TEST, Tue Jan 21 17:55:12 2020, Marlène, MUST2, Hardware, , Ovv error on the -5V of CAEN boards
|
The Ovv error shows on the -5V (first one) of the 3 board (5,3.3,10V for MUST2§squares)
It means that the voltage is over the asked value.
If we ask 5V, we get 5.5V in reality
|
|
Fixed, TEST, Wed Jan 22 15:53:25 2020, Marlène, GRIT, Hardware, , Changes for MUGAST2020
|
Changes were made for MUGAST 2020 :
1- the board for MG10 before (2nd square) is now for MG6 new trap
2- the board for MG9 is put vertical and used for the MUST2 at 90 deg
|
|
Fixed, , Wed Jan 22 18:39:54 2020, Marlène & Franco, GRIT, Hardware, , Tests of the new box
|
The new box has been tested together with the new CAEN SY4527 power supply. We connected a laptop with Linux to the power supply by means of an ethernet
cable and communicated with it by opening a browser (http://192.168.0.1, then username: admin and pwd: admin). To control the channels we open a terminal,
go to the folder where we saved the file ChannelsController.jar and run the command: java -jar ChannelsController.jar 192.168.0.1 admin admin
|
|
Fixed, TEST, Mon Feb 10 18:42:23 2020, Franco&Marlène, GRIT, Hardware, , New MUGAST detectors MG2 MG6
|
MG2 and MG6 have been mounted in the chamber.
MG2 reference number is 3227_10 thickness=468um
|
|
Fixed, TEST, Wed Feb 12 16:24:52 2020, Marlène, Freddy & Franco, MUST2, Hardware, , Modifications on the electronic scheme
|
We cleaned the electronic scheme.
Now the HF CLEAN VAMOS is taken directly from VAMOS and not re-cleaned by us.
TACs are all ok. Inspection lines have been checked and labeled.
|
|
Fixed, , Fri Feb 14 10:26:46 2020, Franco&Marlène, GRIT, Hardware, , HT BT screenshots before e775s
|
| Detectors are cooled down to 0 deg. |
|