Fixed, e744, Fri May 4 23:58:07 2018, iulian, RUN, General, 3-alpha, Run #203 alfa source & 60co source 
|
[U][B]run #203[/B][/U]
alpha source & 60co source
|
|
Fixed, e744, Thu May 10 14:38:41 2018, iulian, EXL-PPT, Hardware, N/A, Mesytech settings
|
Tried unsuccessfully to change the gain on EXL energies.
Looking at the inspection lines noticed that all the EXL signals were inverted (negative) and we were coding only the pole zero part of the signals.
|
|
Pinned, e744, Fri May 11 14:00:48 2018, iulian, EXL-PPT, Hardware, N/A, Mesytech settings
|
[quote="iulian"]Tried unsuccessfully to change the gain on EXL energies.
Looking at the inspection lines noticed that all the EXL signals were inverted (negative) and we were coding only the pole zero part of the signals.
|
|
Fixed, e744, Sat May 12 08:54:42 2018, iulian, MUST2, General, 3-alpha, Run #114 T1-T5 trigger 3alpha source calib run
|
[U][B]Run #214[/B][/U]
Trigger T1-T5 & gamma
3 alpha run
|
|
Ongoing, e744, Sat May 12 20:09:09 2018, iulian, MUST2, General, 3-alpha, Run #115 3 alfa run Calibration T1-T5 trigger
|
[U][B]Run #215[/B][/U]
Trigger T1-T5
3 alpha run
|
|
Ongoing, e744, Sun May 13 12:09:55 2018, iulian, MUST2, General, 3-alpha, Run #116 3 alfa run Calibration T1-T5 trigger
|
[U][B]Run #115[/B][/U]
3 alfa run Calibration T1-T5 trigger
start 12h10
|
|
Pending, e744, Sun May 13 13:32:44 2018, iulian, ONLINE, Software, N/A, start_online ilegal instruction fault
|
From time to time the start_online code gives an ilegal instruction error and crash... Once the ctrl-c pressed it shows:
|
|
Fixed, e744, Wed May 16 11:30:21 2018, iulian, EXL-PPT, General, 60Co, run 302 60Co source
|
[U][B]Run #302[/B][/U]
60 Co source PPT & EXL trigger
|
|
Ongoing, e744, Wed May 16 21:45:47 2018, iulian, MUST2, Software, N/A, Run #323 Calimero T1-T4 strips X
|
[U][B] Run #323[/B][/U]
Calimero T1-T4 strips X |
|
Ongoing, e744, Wed May 16 22:03:13 2018, iulian, EXL-PPT, Software, 60Co, run #324 60Co
|
[U][B]run #324[/B][/U]
60Co
|
|
Pinned, e744, Thu May 17 12:04:45 2018, iulian, EXL-PPT, Hardware, 60Co, EXL delay of ADC Codding window
|
EXL timing delays for Mesitech module 2 & 1
Module 1
|
|
Ongoing, e744, Thu May 17 18:29:16 2018, iulian, MUST2, General, 3-alpha, Run #333 Last alfa run before experiment
|
Run #333
3a source
T1-T5 trigger
|
|
Pinned, e744, Wed May 23 15:10:15 2018, iulian, OTHER, General, N/A, Procedure to start stop RUNS
|
| |
|
Fixed, e744, Thu May 24 01:53:28 2018, iulian, RUN, General, N/A, run 438 Lise trigger
|
run 438 D4 in
run 439 d6 in.
|
|
Ongoing, e744, Thu May 24 02:30:52 2018, iulian, RUN, General, N/A, RUN 440 14N no target trigger Must & cats %100
|
RUN 440
14N beam \
no target
|
|
Fixed, e744, Thu May 24 03:21:37 2018, iulian, OTHER, Hardware, N/A, Position measurements Must2/PPT/EXL
|
| |
|
Fixed, e744, Thu May 24 03:57:34 2018, iulian, RUN, General, N/A, run 442 Lise trigger d6
|
| |
|
Fixed, e744, Thu May 24 04:20:34 2018, iulian, RUN, General, N/A, run 443 T1-t5 triggers
|
run 443
T1-T5 triggers
|
|
Pinned, e744, Thu May 24 05:44:56 2018, iulian, RUN, General, N/A, Important::analysis of the run 443/ things to do
|
[I][B]No stop on t5, but TAC MM_CATS ok.. So two possibilities:
1) Stop Cable not connected on Muvi2
2) Problem with the validation of CATS by FAG
|
|
Ongoing, e744, Thu May 24 05:59:44 2018, iulian, MUST2, General, N/A, run 444 t1-t4 trigger no target 14n beam
|
run 444
t1-t4 trigger
no target
|
|