|
Fixed, e744s, Mon Jul 1 16:45:19 2019, OttoTime, RUN, General, N/A, TimeCalibratorRun
|
*** Run Time Calibrator FSC ***
- Run: 144
- MUVI: MUVI2
- Side : MUFEE X (Junction)
- Telescope: 1, 2, 3, 4 |
|
Fixed, e786s, Mon Jul 1 16:47:40 2019, OttoRun, RUN, General, Cryo-3He, Run99
|
*************************
Run : 99
*************************
Start at 2019-07-01 16:45:20.515273
target 700mb
Brho0=0.90 Tm
DC pressure 6 mbar
IC pressure 120 mbar
CATS2 inserted
AGATA position +51-25 mm
TRIGGER :
- CMG
- M2
- VAMOS%1000
- CATS%1000
all X on MUVI disabled from trigger
all threshold of MUVI1 at 1 MeV to avoid as much as possible noise
LN filling problem solved !!!
pressure of the target slowly increasing about 820 mbar
We are filling the target to reach 1000 mbar
test cats1
time calibration run
New line added just for clarity!!!
Bye Bye!
Salut!
Ok! Ok!
Stop at 2019-07-01 17:09:43.722886
Stop comment: MG11_MG7_X_time calibration |
|
Fixed, e744s, Mon Jul 1 17:09:00 2019, OttoTime, RUN, General, N/A, TimeCalibratorRun
|
*** Run Time Calibrator FSC ***
- Run: 144
- MUVI: MUVI2
- Side : MUFEE Y (Ohmic)
- Telescope: 1, 2, 3, 4 |
|
Fixed, e786s, Mon Jul 1 17:09:45 2019, OttoRun, RUN, General, Cryo-3He, Run100
|
*************************
Run : 100
*************************
Start at 2019-07-01 17:09:01.651618
target 700mb
Brho0=0.90 Tm
DC pressure 6 mbar
IC pressure 120 mbar
CATS2 inserted
AGATA position +51-25 mm
TRIGGER :
- CMG
- M2
- VAMOS%1000
- CATS%1000
all X on MUVI disabled from trigger
all threshold of MUVI1 at 1 MeV to avoid as much as possible noise
LN filling problem solved !!!
pressure of the target slowly increasing about 820 mbar
We are filling the target to reach 1000 mbar
test cats1
time calibration run
New line added just for clarity!!!
Bye Bye!
Salut!
Ok! Ok!
Stop at 2019-07-01 17:32:44.640169
Stop comment: |
|
Fixed, e744s, Mon Jul 1 17:32:40 2019, OttoTime, RUN, General, N/A, TimeCalibratorRun
|
*** Run Time Calibrator FSC ***
- Run: 144
- MUVI: MUVI3
- Side : MUFEE X (Junction)
- Telescope: 1, 2, 3, 4 |
|
Fixed, e786s, Mon Jul 1 17:32:46 2019, OttoRun, RUN, General, Cryo-3He, Run101
|
*************************
Run : 101
*************************
Start at 2019-07-01 17:32:41.600588
target 700mb
Brho0=0.90 Tm
DC pressure 6 mbar
IC pressure 120 mbar
CATS2 inserted
AGATA position +51-25 mm
TRIGGER :
- CMG
- M2
- VAMOS%1000
- CATS%1000
all X on MUVI disabled from trigger
all threshold of MUVI1 at 1 MeV to avoid as much as possible noise
LN filling problem solved !!!
pressure of the target slowly increasing about 820 mbar
We are filling the target to reach 1000 mbar
test cats1
time calibration run
New line added just for clarity!!!
Bye Bye!
Salut!
Ok! Ok!
Stop at 2019-07-01 17:55:52.679255
Stop comment: |
|
Fixed, e744s, Mon Jul 1 17:56:06 2019, OttoTime, RUN, General, N/A, TimeCalibratorRun
|
*** Run Time Calibrator FSC ***
- Run: 144
- MUVI: MUVI3
- Side : MUFEE Y (Ohmic)
- Telescope: 1, 2, 3, 4 |
|
Fixed, e786s, Mon Jul 1 17:56:10 2019, OttoRun, RUN, General, Cryo-3He, Run102
|
*************************
Run : 102
*************************
Start at 2019-07-01 17:56:07.663936
target 700mb
Brho0=0.90 Tm
DC pressure 6 mbar
IC pressure 120 mbar
CATS2 inserted
AGATA position +51-25 mm
TRIGGER :
- CMG
- M2
- VAMOS%1000
- CATS%1000
all X on MUVI disabled from trigger
all threshold of MUVI1 at 1 MeV to avoid as much as possible noise
LN filling problem solved !!!
pressure of the target slowly increasing about 820 mbar
We are filling the target to reach 1000 mbar
test cats1
time calibration run
New line added just for clarity!!!
Bye Bye!
Salut!
Ok! Ok! |
|
Fixed, e786s, Mon Jul 1 17:56:36 2019, OttoRun, RUN, General, Cryo-3He, Run95
|
*************************
Run : 95
*************************
Start at 2019-07-01 15:15:38.418712
target 700mb
Brho0=0.90 Tm
DC pressure 6 mbar
IC pressure 120 mbar
CATS2 inserted
AGATA position +51-25 mm
TRIGGER :
- CMG
- M2
- VAMOS%1000
- CATS%1000
all X on MUVI disabled from trigger
all threshold of MUVI1 at 1 MeV to avoid as much as possible noise
LN filling problem solved !!!
pressure of the target slowly increasing about 820 mbar
We are filling the target to reach 1000 mbar
test cats1
time calibration run
New line added just for clarity!!!
Bye Bye!
Salut!
Ok! Ok! |
|
Fixed, e786s, Tue Jul 2 10:30:10 2019, OttoRun, RUN, General, Cryo-3He, Run96
|
*************************
Run : 96
*************************
Start at 2019-07-01 15:39:55.733031
target 700mb
Brho0=0.90 Tm
DC pressure 6 mbar
IC pressure 120 mbar
CATS2 inserted
AGATA position +51-25 mm
TRIGGER :
- CMG
- M2
- VAMOS%1000
- CATS%1000
all X on MUVI disabled from trigger
all threshold of MUVI1 at 1 MeV to avoid as much as possible noise
LN filling problem solved !!!
pressure of the target slowly increasing about 820 mbar
We are filling the target to reach 1000 mbar
test cats1
time calibration run
New line added just for clarity!!!
Bye Bye!
Salut!
Ok! Ok!
Stop at 2019-07-02 10:30:11.518345
Stop comment:
Stop at 2019-07-02 10:30:44.954507
Stop comment: |
|
Fixed, , Thu Jul 11 11:40:18 2019, Marlène & Franco, OTHER, Hardware, , Some changes in the electronic scheme
|
- We checked the TACs with a time calibrator, all of them are working. Maybe to check the ADCs if some timings are not there during the exp.
- We set the possibility to have MUST2 divided by 100 (on a separate chain) in case of high rate on GMT channel number 7.
- We are now taking as input of the HF the clean HF validated by VAMOS instead of cleaning it on our side through the coincidence with FAG. This is sent to make the STOP of all TACs and MUVIs.
- We sent the OR of MUST2-MUGAST-SQUARES in an additional FIFO with cables of the same length (10 ns) and the output sent to VAMOS and to the TAC called Si-CATS in the acquisition. |
Fixed, e768s, Fri Jul 12 12:07:56 2019, mugast, OTHER, General, N/A, Masks for MUST2 
|
Masks for MUST2 are now mounted.
NOTE: one mask is not properly screwed (top left) and should be mounted again on Monday morning when we open.
Masks cover theta_lab < 38 deg, corresponding to < 30 pps of 15O for 15O+19F elastic channel assuming 2e7 pps of 15O and 1.25 mg/cm2 of LiF. |
|
Fixed, e768s, Fri Jul 12 15:04:35 2019, OttoRun, RUN, General, 3-alpha, Run303
|
*************************
Run : 303
*************************
Start at 2019-07-12 15:03:55.487806
3 alpha calibration run
+ MM2 masks
+ suppressed pedestals
Square detectors:
+ MG10: all X &Y strips masked;
+ MG9 removed
Stop at 2019-07-12 15:05:24.820669
Stop comment: type your message here |
|
Fixed, e768s, Fri Jul 12 15:05:42 2019, OttoRun, RUN, General, 3-alpha, Run303
|
*************************
Run : 303
*************************
Start at 2019-07-12 15:05:39.990342
3 alpha calibration run
+ MM2 masks
+ suppressed pedestals
Square detectors:
+ MG10: all X &Y strips masked;
+ MG9 removed
Stop at 2019-07-12 15:21:45.059356
Stop comment:
Stop at 2019-07-12 16:21:07.294470
Stop comment: type your message here |
|
Fixed, e768s, Fri Jul 12 16:22:04 2019, OttoRun, RUN, General, 3-alpha, Run303
|
*************************
Run : 303
*************************
Start at 2019-07-12 16:22:02.189158
3 alpha calibration run
+ MM2 masks
+ suppressed pedestals
Square detectors:
+ MG10: all X &Y strips masked;
+ MG9 removed
Stop at 2019-07-12 16:33:58.493008
Stop comment: type your message here |
|
Fixed, e768s, Fri Jul 12 16:35:10 2019, OttoRun, RUN, General, 3-alpha, Run303
|
*************************
Run : 303
*************************
Start at 2019-07-12 16:35:04.481793
3 alpha calibration run
+ MM2 masks
+ suppressed pedestals
Square detectors:
+ MG10: all X &Y strips masked;
+ MG9 removed
Stop at 2019-07-12 16:38:40.222071
Stop comment: type your message here |
|
Fixed, e768s, Fri Jul 12 16:42:22 2019, OttoRun, RUN, General, 3-alpha, Run303
|
JUNK
*************************
Run : 303
*************************
Start at 2019-07-12 16:41:50.518089
3 alpha calibration run
+ MM2 masks
+ suppressed pedestals (new pedestal for all trap detectors)
Square detectors:
+ MG10: not biased
+ MG9 removed
Stop at 2019-07-12 16:43:54.495178
Stop comment: type your message here |
|
Fixed, e768s, Fri Jul 12 16:45:00 2019, OttoRun, RUN, General, 3-alpha, Run304
|
JUNK
*************************
Run : 304
*************************
Start at 2019-07-12 16:44:54.903528
3 alpha calibration run
+ MM2 masks
+ suppressed pedestals (new pedestal for all trap detectors)
Square detectors:
+ MG10: not biased
+ MG9 removed
Stop at 2019-07-12 16:46:13.603283
Stop comment: |
|
Fixed, e768s, Fri Jul 12 16:58:52 2019, OttoRun, RUN, General, 3-alpha, Run305
|
JUNK
*************************
Run : 305
*************************
Start at 2019-07-12 16:58:50.871657
3 alpha calibration run
+ MM2 masks
+ suppressed pedestals (new pedestal for all trap detectors)
Square detectors:
+ MG10: not biased
+ MG9 removed
Stop at 2019-07-12 17:00:35.578929
Stop comment: type your message here |
|
Fixed, e768s, Fri Jul 12 17:08:58 2019, OttoRun, RUN, General, 3-alpha, Run305
|
JUNK no pedestal suppression on MG3
*************************
Run : 305
*************************
Start at 2019-07-12 17:08:47.400117
3 alpha calibration run
+ MM2 masks
+ suppressed pedestals (new pedestal for all trap detectors)
Square detectors:
+ MG10: not biased
+ MG9 remove
Pedestals shifted on MG3 due to noise on one over 2 mates
Stop at 2019-07-12 17:16:35.681417
Stop comment: |
|