Fixed, e768s, Mon Jul 22 17:54:49 2019, Christian and Jeremie, AGATA, General, LiF, Comparison EGamma 19Ne, Q8 vs Q9 
|
1) Beam velocity from VAMOS for AGATA doppler correction. Beta is understandable for the three main charge states seen (with Q9 and Q10 as the transfer
states, and centroid shifted higher for Q10 state, possibly because of reduced acceptance for the very high-lying states.
|
|
Fixed, com2019, Tue Apr 2 16:24:06 2019, marlene freddy, OTHER, General, N/A, Commissioning proposal
|
| |
|
Fixed, e768s, Mon Jul 22 16:54:33 2019, Marlène, Franck, François & Nicolas, BEAM, General, , Cheking beam transmission from G1 profiler to VAMOS
|
Goal:
Estimate beam transmission from profiler to VAMOS (FP)
|
|
Fixed, e768s, Tue Jul 23 14:33:03 2019, Marlène, Yorick, Faïrouz & Nicolas, BEAM, General, , Cheking beam transmission from G1 profiler to VAMOS
|
Goal:
Estimate beam transmission from profiler to VAMOS (FP)
We question whether the factor of two found yesterday (VAMOS/Profiler ~ 0.5) could be due:
|
|
Fixed, com2019, Mon Apr 8 10:58:16 2019, Adrien, OFFLINE, General, CD2, Checked alignement of the different Silicon at backward angle
|
Here is a plot of Ex for all the com. stats detector by detector.
The Spectrum are overall well aligned. |
|
Fixed, e768s, Tue Jul 30 07:49:09 2019, Teodora & Franco, RUN, General, LiF, Check beam intensity and profile run158 h 8:00
|
| |
|
Fixed, e768s, Fri Jul 26 23:58:08 2019, Andres & Franco, RUN, General, LiF, Check beam intensity and profile run152 h 23.40
|
| |
|
Fixed, e768s, Fri Jul 26 19:47:18 2019, Andres & Franco, RUN, General, LiF, Check beam intensity and profile run152 h 19.30
|
| |
|
Fixed, e744s, Thu Apr 11 02:54:09 2019, mugast, RUN, General, , Changing Brho to 0.51 Tm starting run 70
|
| |
|
Fixed, e793s, Tue Mar 10 18:46:13 2020, Franco & Marlène, GRIT, Hardware, , Changes in MUGAST
|
- MG6 (FZ) is disconnected.
- MG7 (500um) is dismounted and MG8 (375um) is replacing it.
- The Y kapton of the annular has been changed.
|
|
Fixed, TEST, Wed Jan 22 15:53:25 2020, Marlène, GRIT, Hardware, , Changes for MUGAST2020
|
Changes were made for MUGAST 2020 :
1- the board for MG10 before (2nd square) is now for MG6 new trap
2- the board for MG9 is put vertical and used for the MUST2 at 90 deg
|
|
Fixed, e744s, Thu Apr 11 19:19:21 2019, Iulian Beyhan, RUN, General, N/A, Change target CH2 to no target
|
| Target hole is now removed -> No target |
|
Fixed, e744s, Sun Apr 14 15:05:06 2019, A. Lemasson, VAMOS, Hardware, , Change of Offset in DC Numexo
|
[LIST]
[*] Increasing offset to minimize saturation.
[*] Reducing DC Threholds
|
|
Fixed, , Wed Jan 23 12:24:10 2019, Marlène, GRIT, General, , Change cable MG1T - Exchange of detectors named MG9C & MG10C
|
23/01/19
Change of the HT/BT cable of MG1T (the one that had a short cut before when the chamber was closed)
|
|
Fixed, e793s, Mon Mar 15 10:18:37 2021, Taras, cyril, Léo, ONLINE, Hardware, CD2, Cats2 tripped
|
Cats2 tripped with vamos, had to be reset
Beam is back |
|
Fixed, com2019, Wed Apr 3 11:03:53 2019, Adrien Matta, CATS, Hardware, N/A, Cats mask will be shifted
|
The propulsif supporting the cats mask is leaking.
It will be tighten to fix the leak, this lead to a small shift toward the left of the beam when looking at vamos. |
|
Fixed, TEST, Fri Jan 18 15:32:50 2019, Adrien Valérian, GRIT, General, N/A, Calimero tests Muvi2 MM7 MG10C
|
After disabling nptool Multithreading, online is working fine again.
Concerning Calimero, it is currently working both on MUVI1 and MUVI2 for the X at least.
|
|
Fixed, TEST, Wed Jan 16 17:36:30 2019, Valérian-Marlène, GRIT, General, N/A, Calimero tests - How to configure Calimero in GECO
|
Tests of Calimero time calibration with MUVI1 channel 2 (MM2)
1- channel 3 of all mates selected (see screeshots)
|
|
Fixed, TEST, Tue Mar 5 15:53:04 2019, iulian Marlene, MUST2, Software, N/A, Calimero problems
|
problems with Calimero solved by killing some processes on lpcgrit related with Narval.
to find the processes on lpcgrit:
ps aux | grep Cali*
|
|
Fixed, TEST, Tue Mar 5 18:03:24 2019, iulian Marlene, MUST2, Software, N/A, Calimero problem on Y side
|
| Calimero not working properly on Y side of any mm detector |
|