Fixed, e793s, Sun Mar 14 15:52:36 2021, Faïrouz, Juan Lois, Wilton, RUN, General, CD2, run62 screenshots at 15h52 (14/03/2021) 8x
|
|
|
Fixed, e793s, Sun Mar 14 12:02:10 2021, Faïrouz, Juan Lois, RUN, General, CD2, run62 screenshots at 11h57 (14/03/2021) 8x
|
|
|
Fixed, e793s, Sun Mar 14 02:24:22 2021, Léo, Serge, Nishu, ONLINE, General, CD2, run62 screenshots at 02:25 7x
|
|
|
Fixed, e793s, Sun Mar 14 00:12:41 2021, Léo, Serge, Nishu, ONLINE, General, CD2, run62 screenshots at 00h13 10x
|
|
|
Fixed, e793s, Sat Mar 13 05:33:41 2021, Faïrouz, Juan Lois, RUN, General, CD2, run61 screenshots at 5h30 8x
|
|
|
Fixed, e793s, Sat Mar 13 03:50:54 2021, Faïrouz, Juan Lois, RUN, General, CD2, run61 screenshots at 3h44 8x
|
|
|
Fixed, e793s, Sat Mar 13 01:41:21 2021, Juan Lois & faïrouz, RUN, General, CD2, run61 screenshots at 1h40 8x
|
|
|
Fixed, e793s, Thu Mar 11 23:30:27 2021, Faïrouz, Franco, RUN, General, CD2, run56 screenshots at 23h20 8x
|
|
|
Fixed, e793s, Thu Mar 11 20:23:58 2021, Faïrouz, Franco, RUN, General, CD2, run56 screenshots at 20h18 8x
|
|
|
Fixed, e793s, Fri Mar 12 06:23:44 2021, Taras, Nishu, Chloe, Charlie, RUN, General, CD2, run56 screenshots at 06h15 10x
|
| Screenshots attached |
|
Fixed, e793s, Fri Mar 12 04:19:51 2021, Taras, Nishu, Chloe, Charlie, RUN, General, CD2, run56 screenshots at 04h18 14x
|
| Images attached. |
|
Fixed, e793s, Fri Mar 12 02:01:52 2021, Taras, Nishu, Chloe, Charlie, RUN, General, CD2, run56 screenshots at 02h10 10x
|
| screenshots of run 56 attached below |
|
Fixed, e793s, Thu Mar 11 11:07:05 2021, mugast, OFFLINE, General, CD2, run53 - Egamma vs Ex
|
|
|
Fixed, TEST, Tue Mar 5 18:18:46 2019, iulian Marlene, MUST2, Hardware, 3-alpha, run 97 3a run Muvi3 night run
|
Run 87
stop@ 5:42 am
3a run Muvi3 (MM)
-4 deg
pedestals aligned and suppressed |
|
Fixed, TEST, Thu Mar 7 09:29:47 2019, Marlene, GRIT, General, , run 96 double alpha source run shifted 60mm
|
RUN 96
double alpha source
MG1
MG3
MG4
MG5
MG7
-
-
MG11
MM1
MM2
MM3
MM4
Missing strips in Y the same as in run 40
Problem with the annular MG11 -> no current when bias is put... --> to be checked
Problem with the insertion of the target holder --> solved
I also checked again MG9 (still noisy)
and MG10 with 140V I=0,52uA and counting rate is the same order of magnitude as trapezoid. Spectra are OK (not saved). |
|
Fixed, e744s, Fri Apr 12 08:01:12 2019, valerian, RUN, General, CH2, run 88 screenshots 11x
|
|
|
Fixed, TEST, Tue Mar 5 17:48:38 2019, iulian Marlene, MUST2, Software, N/A, run 82 Gamme 600 ns Time Calibration run (Calimero) on MUVI 3 MM4 X . good run
|
Run 82
Calimero on Muvi3 MM4(X)
Gamme 600 ns |
|
Fixed, TEST, Tue Mar 5 17:11:29 2019, iulian Marlene, MUST2, Software, N/A, run 81 Gamme 600 ns Time Calibration run (Calimero) on MUVI 3 MM3 X . good run
|
Run 81
Run 80 bad
Calimero on Muvi3 MM3(X)
Gamme 600 ns
Procedure:
0) HT on the detectors Off
1) Apply Das config
2) Put Das offline
3) Start Geco
4) Activate on each of the sector to calibrate the X side (see bellow image)
5) execute Calimero.exe in calimero directory
6) modify the calimero config on Geco (see bellow near config button)
7) Start the run in RCC
8) Start calimero (start button in Geco) |
|
Fixed, TEST, Tue Mar 5 16:42:56 2019, iulian Marlene, MUST2, Software, N/A, run 79 Gamme 600 ns Time Calibration run (Calimero) on MUVI 3 MM2 X . good run
|
Run 79
Run 78 bad
Calimero on Muvi3 MM2(X)
Gamme 600 ns
Procedure:
0) HT on the detectors Off
1) Apply Das config
2) Put Das offline
3) Start Geco
4) Activate on each of the sector to calibrate the X side (see bellow image)
5) execute Calimero.exe in calimero directory
6) modify the calimero config on Geco (see bellow near config button)
7) Start the run in RCC
8) Start calimero (start button in Geco) |
|
Fixed, TEST, Tue Mar 5 16:20:11 2019, iulian Marlene, MUST2, Software, N/A, run 77 Gamme 600 ns Time Calibration run (Calimero) on MUVI 3 MM1 X . good run
|
Run 76
Calimero on Muvi3 MM1(X)
Gamme 600 ns
Procedure:
0) HT on the detectors Off
1) Apply Das config
2) Put Das offline
3) Start Geco
4) Activate on each of the sector to calibrate the X side (see bellow image)
5) execute Calimero.exe in calimero directory
6) modify the calimero config on Geco (see bellow near config button)
7) Start the run in RCC
8) Start calimero (start button in Geco) |
|