Status |
ExpNbr |
Date |
Author |
Type |
Category |
Target-Source |
Subject |
Fixed | e768s |
Fri Jul 19 00:01:43 2019 |
OttoRun | RUN | General | N/A | Run100 |
*************************
Run : 100
*************************
Start at 2019-07-18 23:15:56.464535
Pedestal calibration of MUGAST /MUST2 detectors WITHOUT PEDESTAL ALIGNMENT
Internal Pulser on channel 1 of Mate 1 X
Try with new pedestals of MG3 (measured at 17h11 and saved as pedestal_muvi2sec2_18juil19)
Previous pedestals were saved as pedestal_muvi2sec2
Stop at 2019-07-19 00:08:11.676196
Stop comment: |
Fixed | e768s |
Fri Jul 19 00:08:13 2019 |
OttoRun | RUN | General | N/A | Run104 |
*************************
Run : 104
*************************
Start at 2019-07-19 00:06:02.719387
Pedestal calibration of MUGAST /MUST2 detectors WITHOUT PEDESTAL ALIGNMENT
Internal Pulser on channel 1 of Mate 1 X
Try with new pedestals of MG3 (measured at 17h11 and saved as pedestal_muvi2sec2_18juil19)
Previous pedestals were saved as pedestal_muvi2sec2 |
Fixed | e768s |
Fri Jul 19 00:08:51 2019 |
OttoRun | RUN | General | N/A | Run105 |
*************************
Run : 105
*************************
Start at 2019-07-19 00:08:48.562904
Tuning 15O beam to center on optical axis and remove contribution from natC part of the target
Stop at 2019-07-19 00:58:24.956373
Stop comment: |
Attachment 1: run_105-15O-beamspot-optimization.png
|
|
Attachment 2: IMG_20190719_010634_crop.jpg
|
|
Fixed | e768s |
Fri Jul 19 00:59:00 2019 |
OttoRun | RUN | General | LiF | Run106 |
*************************
Run : 106
*************************
Start at 2019-07-19 00:58:37.270080
Stop at 2019-07-19 01:00:43.108147
Stop comment: |
Fixed | e768s |
Fri Jul 19 01:32:17 2019 |
OttoRun | RUN | General | LiF | Run107 |
*************************
Run : 107
*************************
Start at 2019-07-19 01:00:49.000867
Stop at 2019-07-19 01:32:18.881037
Stop comment: |
Fixed | e768s |
Fri Jul 19 01:32:20 2019 |
OttoRun | RUN | General | LiF | Run108 |
*************************
Run : 108
*************************
Start at 2019-07-19 01:05:04.198626
Stop at 2019-07-19 02:01:09.195123
Stop comment:
Stop at 2019-07-19 02:16:54.064899
Stop comment: |
Fixed | e768s |
Fri Jul 19 02:19:51 2019 |
OttoRun | RUN | General | LiF | Run110 |
*************************
Run : 110
*************************
Start at 2019-07-19 02:13:34.456709
RUN 110 Coupled with AGATA
15O : 1e7 pps
Brho 0.656
target 1.25 mg/cm 7LiF |
Fixed | e768s |
Fri Jul 19 02:22:12 2019 |
OttoRun | RUN | General | LiF | Run111 |
*************************
Run : 111
*************************
Start at 2019-07-19 02:19:49.799405
JUNK
10 Coupled with AGATA
15O : 1e7 pps
Brho 0.656
target 1.25 mg/cm 7LiF
Stop at 2019-07-19 02:22:24.337284
Stop comment: |
Fixed | e768s |
Fri Jul 19 02:27:22 2019 |
OttoRun | RUN | General | LiF | Run112 |
*************************
Run : 112
*************************
Start at 2019-07-19 02:25:09.701469
coupled with AGATA
15O @ 1.5e7 ppps
Brho=0.556
Target : LiF n°1 1.25 mg/cm2
trigger :
MG
square
MM
Vamos%100
BaF2%100
removed suppression of overflow in energy for MM & square
Stop at 2019-07-19 10:07:19.632461
Stop comment: |
Fixed | e768s |
Fri Jul 19 10:35:05 2019 |
OttoRun | RUN | General | LiF | Run113 |
*************************
Run : 113
*************************
Start at 2019-07-19 10:35:00.811685
JUNK
Stop at 2019-07-19 10:42:58.694755
Stop comment: type your message here
Stop at 2019-07-19 10:51:03.268053
Stop comment: type your message here |
Fixed | e768s |
Fri Jul 19 12:06:44 2019 |
OttoRun | RUN | General | LiF | Run115 |
*************************
Run : 115
*************************
Start at 2019-07-19 10:53:00.945262
same conditions as before
LiF target
Brho=0556
GMT triggers :
MG
Square
MM
Vamos div
Baf2 div
Beam optimization during this run to try to improve intensity |
Attachment 1: run_115_scaler1.png
|
|
Attachment 2: run_115_IC_IC.png
|
|
Attachment 3: run_115_REC.png
|
|
Attachment 4: run_115_TAC.png
|
|
Attachment 5: run_115_IC2.png
|
|
Attachment 6: run_115_IC.png
|
|
Attachment 7: run_115_Ewire.png
|
|
Attachment 8: run_115_DCY.png
|
|
Attachment 9: run_115_DCXpng.png
|
|
Attachment 10: run_115_MM_MG_ERaw.png
|
|
Attachment 11: run_115_Tac.png
|
|
Attachment 12: run_115_MG_ToF.png
|
|
Attachment 13: run_115_MM_DeE.png
|
|
Attachment 14: run_115_MM_Tof.png
|
|
Attachment 15: run_115_MG_impact.png
|
|
Attachment 16: run_115_MM_impact.png
|
|
Attachment 17: run_115_scaler2.png
|
|
Fixed | e768s |
Fri Jul 19 16:43:08 2019 |
OttoRun | RUN | General | LiF | Run116 |
*************************
Run : 116
*************************
Start at 2019-07-19 16:42:58.163547
Stop at 2019-07-20 04:34:58.716855
Stop comment: type your message here
Stop at 2019-07-20 10:40:22.875934
Stop comment: loss beam, premary beam monitor |
Fixed | e768s |
Sat Jul 20 14:00:22 2019 |
OttoRun | RUN | General | LiF | Run117 |
*************************
Run : 117
*************************
Start at 2019-07-20 13:59:36.817451
H2O cold box reset. took a while to reach below 20deg in cave.
beam back.
Stop at 2019-07-20 16:47:36.880786
Stop comment: VXI VAMOS LOST |
Fixed | e768s |
Sat Jul 20 17:00:19 2019 |
OttoRun | RUN | General | LiF | Run118 |
*************************
Run : 118
*************************
Start at 2019-07-20 16:59:33.086411
Start after the overtemperature of VXI VAMOS.
Stop at 2019-07-20 21:11:28.272749
Stop comment: Vamos VXI offline |
Fixed | e768s |
Sat Jul 20 23:18:02 2019 |
OttoRun | RUN | General | LiF | Run119 |
*************************
Run : 119
*************************
Start at 2019-07-20 23:17:24.464827
Start after SECOND overtemperature of VXI VAMOS.
Stop at 2019-07-21 20:12:21.834156
Stop comment: stopped because intensity dropped to 6e6 pps (profiler) PCP working on optimization |
Fixed | e768s |
Sun Jul 21 21:22:58 2019 |
OttoRun | RUN | General | LiF | Run120 |
*************************
Run : 120
*************************
Start at 2019-07-21 21:19:46.530036
beam intensity after optimization 1.6e7 pps
OR VAMOS ~ 1500 Hz
Target: 1.25 mg/cm2 (nb 1) 7LiF
Triggers
MUGAST (backward, MM, 90 deg)
VAMOS %100
BaF2 %100
Stop at 2019-07-21 21:52:56.667021
Stop comment: |
Fixed | e768s |
Sun Jul 21 22:17:18 2019 |
OttoRun | RUN | General | LiF | Run121 |
*************************
Run : 121
*************************
Start at 2019-07-21 21:54:19.075515
beam intensity after optimization 1.6e7 pps
OR VAMOS ~ 1500 Hz
Target: 1.25 mg/cm2 (nb 1) 7LiF
Triggers
MUGAST (backward, MM, 90 deg)
VAMOS %100
BaF2 %100
Stop at 2019-07-22 05:09:23.310656
Stop comment: Problems with AGATA. Need to stop acquisition to recover AGATA validation |
Fixed | e768s |
Mon Jul 22 05:12:13 2019 |
OttoRun | RUN | General | LiF | Run122 |
*************************
Run : 122
*************************
Start at 2019-07-22 05:11:56.885037
beam intensity after optimization 2.0e7 pps
OR VAMOS ~ 1500 Hz
Target: 1.25 mg/cm2 (nb 1) 7LiF
Triggers
MUGAST (backward, MM, 90 deg)
VAMOS %100
BaF2 %100
Stop at 2019-07-22 07:01:32.414292
Stop comment: stop run 122. We wait for Bertrand to optimize the beam centering and size. |
Fixed | e768s |
Mon Jul 22 07:48:03 2019 |
OttoRun | RUN | General | LiF | Run123 |
*************************
Run : 123
*************************
Start at 2019-07-22 07:47:55.021346
beam intensity after optimization 2.0e7 pps
OR VAMOS ~ 1500 Hz
Target: 1.25 mg/cm2 (nb 1) 7LiF
Triggers
MUGAST (backward, MM, 90 deg)
VAMOS %100
BaF2 %100
Stop at 2019-07-22 08:16:58.580316
Stop comment: End of beam position optimization |
Fixed | e768s |
Mon Jul 22 08:26:07 2019 |
OttoRun | RUN | General | LiF | Run124 |
*************************
Run : 124
*************************
Start at 2019-07-22 08:18:38.043920
Restart after beam position optimization by Bertrand to reduce AGATA rate
(probably from beam hitting the target frame)
Beam position in VAMOS FP moved by +15 mm in vertical
-> - 2 mm in vertical on target
Beam intensity: 2.0e7 pps
OR VAMOS ~ 1100 Hz
So the VAMOS/intensity ratio has changed
Target: 1.25 mg/cm2 (nb 1) 7LiF
Triggers:
MUGAST (backward, MM, 90 deg)
VAMOS %100
BaF2 %100
Rates:
FAG: 160
MUGAST: 150
OR AGATA: 1400
OR VAMOS: 1100
Stop at 2019-07-22 10:54:58.589478
Stop comment: stop to recover MG3X |